Repairing a dryer’s push-to-start in 3 easy steps

Written by David Lewis
5 Min read
,

How to tell if you need a new push-to-start switch

you may need to replace the push-to-start switch If your dryer is not starting when you press the button. To test this, open up your dryer and check the wires connected to the switch. If the wires appear damaged or corroded, then it is likely time for a replacement.

Tools needed to fix a push-to-start switch

When it comes to doing a DIY repair on any type of dryer push to start switch, there are a few tools that are required to make sure the job is done correctly. You will need a Push to Start Replacement Switch, a flathead screwdriver, a 1/4″ nut driver or socket wrench, a phone for taking pictures of the wire connections, and a pair of work gloves.

Instructions on how to repair a dryer push-to-start switch

Before you can even think about starting the repair, you first need to unplug your dryer from its power source. This is done as a safety precaution in case you accidentally come in contact with any live wires.

Once you have the dryer unplugged, you can begin the process of repairing your push-to-start switch by pulling the knob off the dryer. Then you will need to remove the control back panel so that you can access the push-to-start switch. It may be helpful to take a photograph of the wire connections before proceeding with the repair. This will come in handy should you ever need to replace the switch again.

WhirlPool Duet Dryer Will not Start but powers on.

Next step

The next step is to identify the push-to-start switch. Usually it will be a small, round piece of plastic with two small prongs sticking out. Once you have identified the switch, you can then begin to disconnect the wires from the old switch and attach them to a new one.

Wiring

Once the wires are attached to the new switch, you can now reattach the control back panel and replace the knob on the front of the dryer. After everything is screwed back together, you will need to set your dryer to neutral settings. This is done by pressing the push-to-start button several times.

The final step is to test the Push-to-Start button to ensure that the repair was successful. To do this, simply wait a few moments and press the button again to see if the dryer functions properly. If the repair fails or if you need additional help, you can always contact support for more insights into home appliance repair.

push-to-start

Expert Tip:

As a pro-tip, always wear your gloves when repairing any type of appliance. This will protect your hands from any sharp edges, hot components, and electrical shocks. Furthermore, make sure all screws are tightened properly and that no loose wires remain after the repair is complete.

Where to get replacement parts for your dryer

Replacement parts for your dryer can easily be found online at a number of popular retailers. Be sure to confirm the exact make and model of your dryer before purchasing the replacement parts to ensure a perfect fit.

Tips to avoid dryer repair in the future

While it is impossible to guarantee that your dryer will never break down in the future, there are a few tips that can help prolong its life and reduce the likelihood of needing a repair. First, make sure to regularly clean out the lint filter. This will help the dryer operate more efficiently and reduce the risk of it overheating. Additionally, it is recommended to use a power surge protector when plugging in your dryer. This will help protect it from any voltage spikes that could damage the major components.

Signs of a malfunctioning dryer motor

If your dryer is malfunctioning and you suspect it is due to a faulty motor, then there are a few signs you can look for. A humming sound when the dryer has been turned on is one sign that the motor may need to be replaced. Additionally, if your dryer is unable to start even after pressing the push-to-start button, then this is another common symptom of a bad motor.

Dos and don’ts for operating your dryer

When it comes to operating your dryer, there are a few do’s and don’ts that should always be followed. DO make sure to keep the lint filter clean, avoid overloading the drum, and use a grounded power plug when connecting the dryer. DON’T use an extension cord to power up the dryer, leave any wet clothing or items inside the dryer, or attempt to repair the dryer yourself without the guidance of an expert.

Common causes of a dryer not starting

There are many possible causes of a dryer not starting, but the most common culprits are usually the push-to-start switch, the door latch, or the motor. If none of these seem to be the issue, then it is highly likely that there is something else wrong with the dryer’s internal components. In this case, it is best to contact a local repair technician for help.

Where to find reliable appliance repair services

If you need to find a reliable appliance repair service, then start by asking friends and family who have used repair services in the past. Additionally, researching online reviews of local companies can be helpful in determining which repair services provide quality results.

Safety tips for working on your dryer

When working on your dryer, always remember to unplug it from the power source and wear work gloves. Additionally, you should refrain from taking apart any parts you are unfamiliar with and consult professional advice if needed.

Checklist for regular maintenance of your dryer

For regular maintenance of your dryer, remember to check the following items every few months: lint filter, exterior vents, and belt tension. Additionally, cleaning the back panel and coils can help with overall performance.

Summary

When it comes to repairing a dryer push-to-start switch, it is essential to have the right tools, follow safety protocols, and gather all necessary information before attempting the repair. Following the steps outlined in this article will provide useful insights into the process of repairing a push-to-start switch, as well as tips for avoiding repairs in the future.

Conclusions

This article has outlined the process of repairing a dryer push-to-start switch, as well as tips for avoiding repairs in the future. The key steps involved are unplugging your dryer, removing the knob and control back panel, identifying the switch, disconnecting the wires from the old switch, attaching them to a new switch, replacing the knob, setting the dryer to neutral settings, testing it, and consulting a professional if needed. Moreover, regular maintenance such as cleaning the lint filter, exterior vents, and coils should be done every few months for optimal operating conditions and performance.

Appliances made simple. 

linkedin facebook pinterest youtube rss twitter instagram facebook-blank rss-blank linkedin-blank pinterest youtube twitter instagram